Compare Products

You have no items to compare.


Shopping Cart

0 item £0.00

My Cart -

0 item

Kobuki YMR-K01-W1 (Turtlebot 2 base)

Availability: Available to Backorder

Exc. VAT: £290.08 Inc. VAT: £348.10



Quick overview

Kobuki is a low-cost mobile research base designed for education and research on state of art robotics. With continuous operation in mind, Kobuki provides power supplies for an external computer as well as additional sensors and actuators. Its highly accurate odometry, amended by our factory calibrated gyroscope, enables precise navigation.

Kobuki is an mobile base for open-source research and development purposes. It can be used to quickly and cheaply build research platforms and also provides access to other open source software, including ROS. The result is a product that can very easily utilise existing 3D sensing technologies and navigation algorithms to develop applications for research.



  • Maximum translational velocity: 70 cm/s
  • Maximum rotational velocity: 180 deg/s (>110 deg/s gyro performance will degrade)
  • Payload: 5 kg (hard floor), 4 kg (carpet)
  • Cliff: will not drive off a cliff with a depth greater than 5cm
  • Threshold Climbing: climbs thresholds of 12 mm or lower
  • Rug Climbing: climbs rugs of 12 mm or lower
  • Expected Operating Time: 3/7 hours (small/large battery)
  • Expected Charging Time: 1.5/2.6 hours (small/large battery)
  • Docking: within a 2mx5m area in front of the docking station

  • PC Connection: USB or via RX/TX pins on the parallel port
  • Motor Overload Detection: disables power on detecting high current (>3A)
  • Odometry: 52 ticks/enc rev, 2578.33 ticks/wheel rev, 11.7 ticks/mm
  • Gyro: factory calibrated, 1 axis (110 deg/s)
  • Bumpers: left, center, right
  • Cliff sensors: left, center, right
  • Wheel drop sensor: left, right
  • Power connectors: 5V/1A, 12V/1.5A, 12V/5A
  • Expansion pins: 3.3V/1A, 5V/1A, 4 x analog in, 4 x digital in, 4 x digital out
  • Audio : several programmable beep sequences
  • Programmable LED: 2 x two-coloured LED
  • State LED: 1 x two coloured LED [Green - high, Orange - low, Green & Blinking - charging]
  • Buttons: 3 x touch buttons
  • Battery: Lithium-Ion, 14.8V, 2200 mAh (4S1P - small), 4400 mAh (4S2P - large)
  • Firmware upgradeable: via usb
  • Sensor Data Rate: 50Hz
  • Recharging Adapter: Input: 100-240V AC, 50/60Hz, 1.5A max; Output: 19V DC, 3.16A
  • Netbook recharging connector (only enabled when robot is recharging): 19V/2.1A DC
  • Docking IR Receiver: left, centre, right
  • Diameter : 351.5mm / Height : 124.8mm / Weight : 2.35kg (4S1P - small)

  • C++ drivers for linux and windows
  • ROS node
  • Gazebo Simulation
  • Contents

  • 1x Kobuki
  • 1x Small Battery Pack
  • 1x Charger
  • 1x USB Cable
  • 1x Power Cable


    The Kobuki is a mobile base. It has sensors, motors and power sources, however by itself, it cannot do anything.

    To be functional, it requires you to build your platform on top of it's shell. On the hardware side, this usually involves adding a netbook or an embedded board to be the computational core for your system and usually a few extra sensors to make it truly functional. On the software side, this involves either building all of your own software or integrating software from other groups with your own development sources.

    This can take time, effort and money. If you want to get started quickly, or a standardised platform for your group you can either use an existing reference platform or ask your nearest distributor to customise a packaged platform for your group.


    Turtlebot 2 - tap into the power of RoS with a complete software framework built around a mobile 3d sensing platform

    Manufacturer part No: YMR-K01-W1