Compare Products

You have no items to compare.

RoboSavvy
Categories

Shopping Cart

0 item £0.00

My Cart -

0 item
Browse By
Category
  1. Controllers & Drivers (25)
  2. SBC & Embedded Computer (15)
  3. Sensors (332)
Compare Products

You have no items to compare.

Electronics

  1. Exc. VAT: £11.08 Inc. VAT: £13.30
    The LPS25HB is an absolute pressure sensor which means that it has an internal vacuum as a reference. (As opposed to differential and gage sensors, see this description by Honeywell for more info) Absolute pressure sensors are often used as altimeters however they can be seen in other applications like the Robotic Finger Sensor v2.

    Availability: In stock

  2. Exc. VAT: £29.25 Inc. VAT: £35.10
    Fingerprint scanners are awesome! Why use a key when you have one right at the tip of your finger? Unfortunately, they're often unreliable or difficult to implement. Well not anymore! This great GT-521F32 fingerprint module from ADH-Tech communicates over TTL Serial so you can easily embed it into your next project. The module itself does all of the heavy lifting behind reading and identifying the fingerprints with an onboard optical sensor and 32-bit ARM Cortex M3 processor.

    Availability: In stock

  3. Exc. VAT: £130.25 Inc. VAT: £156.30
    The Walabot Starter is a small, programmable sensor tool that looks into objects using radio frequency technology sense the environment, bringing highly sophisticated sensing capabilities to your fingertips. This Walabot Starter version uses a three-antenna array to illuminate the area in front of it and sense the returning signals. The signals are produced and recorded by a VYYR2401 A3 System-on-Chip integrated circuit. They are then communicated to a host device (like your phone or computer) using a USB interface, which is implemented using a Cypress controller.

    Availability: In stock

  4. Exc. VAT: £517.42 Inc. VAT: £620.90
    The Walabot Developer is a programmable 3D sensor inside a protective enclosure that looks into objects using radio frequency technology. This technology breaks through known barriers, bringing highly sophisticated sensing capabilities to your fingertips. This Walabot Developer version uses an 18-antenna array to illuminate the area in front of it and sense the returning signals. The signals are produced and recorded by a VYYR2401 A3 System-on-Chip integrated circuit. They are then communicated to a host device (like your phone or computer) using a USB interface, which is implemented using a Cypress controller.

    Availability: In stock

  5. Exc. VAT: £46.00 Inc. VAT: £55.20
    Fingerprint scanners are awesome! Why use a key when you have one right at the tip of your finger? Unfortunately, they're often unreliable or difficult to implement. Well not anymore! This great GT-521F52 fingerprint module from ADH-Tech communicates over TTL Serial so you can easily embed it into your next project. The module itself does all of the heavy lifting behind reading and identifying the fingerprints with an onboard optical sensor and 32-bit ARM Cortex M3 processor.

    Availability: In stock

  6. Exc. VAT: £162.75 Inc. VAT: £195.30
    The Magnetic Imaging Tile uses an array of 64 hall effect sensors to convert magnetic fields to the visual spectrum. That's right! You can now see magnetic fields in real time! As is to be expected, there are caveats: the magnetic sensors used on the tile are some of the most sensitive on the market but you need to be within 1 to 2 centimeters of the tile to get a good image.

    Availability: In stock

  7. Exc. VAT: £12.08 Inc. VAT: £14.50
    The SparkFun Distance Sensor Breakout utilizes the RFD77402 3D ToF (Time of Flight) sensor module from Simblee to give you the most accurate measurements at short range. The RFD77402 uses an infrared VCSEL (Vertical Cavity Surface Emitting Laser) module to measure the amount of time it takes to bounce off a target. This allows low-cost millimeter readings up to two meters! To make it even easier to use this breakout, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1" spaced pins in case you prefer to use a breadboard.

    Availability: In stock

  8. Exc. VAT: £9.33 Inc. VAT: £11.20
    This breakout board makes it easy to use the tiny MMA8452Q accelerometer communicate over I2C in your project. The MMA8452Q is a smart low-power, three-axis, capacitive MEMS accelerometer with 12 bits of resolution. This accelerometer is packed with embedded functions with flexible user programmable options, configurable to two interrupt pins. Embedded interrupt functions allow for overall power savings relieving the host processor from continuously polling data. This version of the SparkFun Triple Axis Accelerometer Breakout includes pre-soldered Qwiic connectors for rapid prototyping and better ease of use. With the connectors already soldered on, you can jump right into using this little board without any assembly!

    Availability: In stock

  9. Exc. VAT: £18.92 Inc. VAT: £22.70
    The NFC-RFID Expansion Board will bring a new world of exciting functionality and application to your Omega2 module. As with other expansions, it will plug into your Onion Expansion, Arduino or Power Dock, and provide you with both NFC and RFID communication. This board makes use of the PN532 controller chip and is embedded in most smart phones and devices that support NFC. It can read and write to tags and cards, communicate with phones (for example payment processing), and ‘act’ like a NFC tag.

    Availability: In stock

  10. Exc. VAT: £28.50 Inc. VAT: £34.20
    The SparkFun Variable Load Kit is a quick-to-assemble board designed to allow users to draw a specific amount of current from a voltage input. This kit can be used to test stability of the power supply under various loads, battery lifetime, safety cutoffs and other design elements. The Variable Load Kit can test supplies of up to 30V at currents ranging from a few mA all the way up to 4A.

    Availability: In stock