Compare Products

You have no items to compare.

RoboSavvy
Categories

Shopping Cart

0 item £0.00

My Cart -

0 item
Shop By
Currently Shopping by:
  1. Remove This Item Use: General carving
  2. Remove This Item Manufacturer: DFRobot
  3. Remove This Item Manufacturer: Inventables

Shopping Options

Category
  1. Inventables (14)
  2. Sparkfun (2)
Use
  1. Engraving (13)
  2. General carving (16)
  3. PCB/circuit board (1)
  4. Routing (6)
  5. Three-dimensional contouring (6)
  6. V carving (7)
Cutting Material
  1. Aluminium (11)
  2. Corian (12)
  3. Linoleum (11)
  4. MDF (12)
  5. Plastic (12)
  6. Plywood (11)
  7. Soft Metals (10)
  8. Wood (11)
Type
  1. Ball Nose (5)
  2. Downcut (8)
  3. Engraving (5)
  4. PCB/circuit board (5)
  5. Straight (8)
  6. Upcut (12)
  7. V bit (2)
  8. Variety pack (8)
Cutting Diameter
  1. 0.01 in (5)
  2. 1/16 in (7)
  3. 1/32 in (6)
  4. 1/4 in (3)
  5. 1/8 in (14)
Shank Diameter
  1. 1/4 in (6.35mm) (3)
  2. 1/8 in (3.175mm) (16)
Flutes
  1. 1 (9)
  2. 2 (15)
  3. 3 (5)
Price
£0 £1593 £0 to £1593
Manufacturer
  1. Carbide 3D (2)
  2. DeWalt (5)
  3. DFRobot (0)
  4. Inventables (16)
  5. JtechPhotonics (5)
  6. Opt Lasers (5)
  7. RoboSavvy (5)
  8. Vectric (5)
Compare Products

You have no items to compare.

Brands

  1. Exc. VAT: £3.50 Inc. VAT: £4.20
    Inventables Solid Carbide Single Flute Upcut End Mill 1/8. The spiral upcut bits pull chips from the cutting surface upwards, leaving a flat bottomed pocket. This provides accurate cuts without chatter in the plastic because the chips are being evacuated away from the cutting edges. This bit is not recommended for wood because it pulls the wood fibers causing tear out.
  2. Exc. VAT: £3.83 Inc. VAT: £4.60
    This end mill has a 2 straight flutes. It works well for materials where the lifting affect of a spiral flute might cause unwanted results, like wood or things with thin laminates or veneers. Best for Cutting Corian, plastic, linoleum, wood, plywood, MDF
  3. Exc. VAT: £8.42 Inc. VAT: £10.10
    1/16 Solid Carbide Upcut Fish Tail Spiral
  4. Exc. VAT: £9.25 Inc. VAT: £11.10

    Ideal for carving plastics

    . These fishtail bits are great for fine detail and inlays. The upcut tip design creates a cleaner edge on the backside of the sheet when cutting through materials. The flute design works well with high speed spindles and high feedrates.
  5. Exc. VAT: £9.25 Inc. VAT: £11.10
    1/16 Solid Carbide Downcut Fish Tail Spiral Bit
  6. Exc. VAT: £12.00 Inc. VAT: £14.40
    1/8 Solid Carbide Downcut Fish Tail Spiral Bit
  7. Exc. VAT: £14.17 Inc. VAT: £17.00
    1/32 Solid Carbide Upcut Fish Tail Spiral
  8. Exc. VAT: £14.17 Inc. VAT: £17.00
    1/32 Solid Carbide Downcut Fish Tail Spiral Bit
  9. Exc. VAT: £30.00 Inc. VAT: £36.00
    This set of 6 bits is great for general purpose wood and plastic cutting.Best for cutting Corian, plastic, linoleum, wood, plywood, MDF.This bit set will get you started on your first or next wood/plastic based prject.
  10. Exc. VAT: £35.17 Inc. VAT: £42.20
    6 bits great for cutting soft metals like aluminum. This set of 6 bits is great for general purpose soft metal cutting. Bits have a shank diameter of 1/8 inch. Up-cut bits expel the cut material upward and smooths the bottom of the cut pass. It pulls heat away from the bit, and is a good choice for plastics, metals, or other materials that are prone to melting or burning.