From what we read on the Korean website (and with the help of Google Translate)the changelog for the new version can be found bellow.
Between 2.30 (the latest available on the English Robobuilder website) and 2.34 there was an interim release (2.31). I'm including the changelog for all of them as 2.31 seems to have made some change in the RBC protocol.
Control Box firmware version is 2.34.
(The model: RBC-08128NNN, RBC-08128YNN, RBC-08128NYN)
<Different>;
- The default position Runtime remove unnecessary movement
- Failed to download files of a certain size motion to remove the problem
Control Box firmware version is 2.31.
(cumulative and included in 2.34)
(The model: RBC-08128NNN, RBC-08128YNN, RBC-08128NYN)
<Different>;
- Motion Run command should not send a response packet upon receiving (1: N communication intended to eliminate the interference).
Control Box firmware version 2.30.
(this version is available on the English Robobuilder website; these features are also cumulative and included in v2.34)
<What>;
- Get Up Automatically (Should have "Acceleration sensor" installed RBC)
: In order to Enter or Exit this mode, press IR remoe button "# + STOP" button together.
You can see PF1 LED is blinking when this mode is entered.
- Continuous Walk: Keep Walking Forward or BackWard function
(This command works when user use Bluetooth Module or PC Communication Cable.)
* This function is NOT supported by IR remote controller.
? Caution
1) If this firmware does not work, please change with the previous firmware.
After the firmware upgrade it _may_ be necessary to perform any (or all) of the following procedures:
(DO NOT perform these procedures unless absolutely necessary; usually these are NOT necessary but we're posting them just for User's Reference).
1) Register the Remote Control on the RBC box.
2) Set the platform mode (press and hold the PF button to set it tot he correct Robot shape).
3) Reset the zero point
You should reffer to the User's Manual as it explains how to perform all of these procedures in detail should you need to do them.
From what we read on the Korean website (and with the help of Google Translate)the changelog for the new version can be found bellow.
Between 2.30 (the latest available on the English Robobuilder website) and 2.34 there was an interim release (2.31). I'm including the changelog for all of them as 2.31 seems to have made some change in the RBC protocol.
Control Box firmware version is 2.34.
(The model: RBC-08128NNN, RBC-08128YNN, RBC-08128NYN)
<Different>;
- The default position Runtime remove unnecessary movement
- Failed to download files of a certain size motion to remove the problem
Control Box firmware version is 2.31.
(cumulative and included in 2.34)
(The model: RBC-08128NNN, RBC-08128YNN, RBC-08128NYN)
<Different>;
- Motion Run command should not send a response packet upon receiving (1: N communication intended to eliminate the interference).
Control Box firmware version 2.30.
(this version is available on the English Robobuilder website; these features are also cumulative and included in v2.34)
<What>;
- Get Up Automatically (Should have "Acceleration sensor" installed RBC)
: In order to Enter or Exit this mode, press IR remoe button "# + STOP" button together.
You can see PF1 LED is blinking when this mode is entered.
- Continuous Walk: Keep Walking Forward or BackWard function
(This command works when user use Bluetooth Module or PC Communication Cable.)
* This function is NOT supported by IR remote controller.
? Caution
1) If this firmware does not work, please change with the previous firmware.
After the firmware upgrade it _may_ be necessary to perform any (or all) of the following procedures:
(DO NOT perform these procedures unless absolutely necessary; usually these are NOT necessary but we're posting them just for User's Reference).
1) Register the Remote Control on the RBC box.
2) Set the platform mode (press and hold the PF button to set it tot he correct Robot shape).
3) Reset the zero point
You should reffer to the User's Manual as it explains how to perform all of these procedures in detail should you need to do them.
In the case of RBC82.56_11.1V.zip I don't have much detailed information.
I just received the file from Robobuilder and posted it for our users to download.
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot vote in polls in this forum
£18.22 inc. VAT
