Is there a simple Labview example for starting with RB-110?

Based on DMP's Vortex processor / SoC this board is a full computer capable of running a standard Windows and Linux installation on the backpack of your robot.
4 postsPage 1 of 1
4 postsPage 1 of 1

Is there a simple Labview example for starting with RB-110?

Post by user_1979 » Mon Mar 28, 2011 8:08 am

Post by user_1979
Mon Mar 28, 2011 8:08 am

Hi everyone,

I need to communicate with a sensor using a I2C bus (I have no experience with this) and the Roboard card RB-110 . I have opened the vi's found in RoBoIOv15b.zip on this website, but I really need a simple example so that I can see how these functions are used. Or a more complicated one that I could analyse my self. A RB-100 one would be fine too.

Would anybody have this available?

Any help would be great,

Thanks

Regards,

User
Hi everyone,

I need to communicate with a sensor using a I2C bus (I have no experience with this) and the Roboard card RB-110 . I have opened the vi's found in RoBoIOv15b.zip on this website, but I really need a simple example so that I can see how these functions are used. Or a more complicated one that I could analyse my self. A RB-100 one would be fine too.

Would anybody have this available?

Any help would be great,

Thanks

Regards,

User
user_1979 offline
Robot Builder
Robot Builder
Posts: 8
Joined: Mon Mar 28, 2011 7:57 am

Re: Is there a simple Labview example for starting with RB-1

Post by roboard » Mon Mar 28, 2011 8:18 am

Post by roboard
Mon Mar 28, 2011 8:18 am

Hi,

the RoBoIO LabVIEW warper is made by Ries, and you can find his post in the following:

http://robosavvy.com/forum/viewtopic.php?t=3913

:)
Hi,

the RoBoIO LabVIEW warper is made by Ries, and you can find his post in the following:

http://robosavvy.com/forum/viewtopic.php?t=3913

:)
roboard offline
Savvy Roboteer
Savvy Roboteer
Posts: 302
Joined: Fri Jul 03, 2009 4:44 am

Post by user_1979 » Tue Mar 29, 2011 7:49 am

Post by user_1979
Tue Mar 29, 2011 7:49 am

Hi Roboard,

Thanks for your help. I have opened the example ("pwm+outp sample") on the link you have send. Because I am new to this, it seems quite specific to pwm signal (no master/slave behaviour) and I find it hard to malke a parallel with I2C.

If anybody had an example (what ever complex it is) dealing with I2, it would be really great.

Regards,

User
Hi Roboard,

Thanks for your help. I have opened the example ("pwm+outp sample") on the link you have send. Because I am new to this, it seems quite specific to pwm signal (no master/slave behaviour) and I find it hard to malke a parallel with I2C.

If anybody had an example (what ever complex it is) dealing with I2, it would be really great.

Regards,

User
user_1979 offline
Robot Builder
Robot Builder
Posts: 8
Joined: Mon Mar 28, 2011 7:57 am

Re: Is there a simple Labview example for starting with RB-1

Post by roboard » Sat Apr 30, 2011 3:15 pm

Post by roboard
Sat Apr 30, 2011 3:15 pm

some information:

Robotis provides a detailed tutorial for interfacing their C DLL with LabVIEW. Their approach is also applicable to RoBoIO.DLL; when the official RoBoIO LabVIEW warper has not been released, if you need to use the new version of RoBoIO in LabVIEW, you may refer to Robotis approach:

http://support.robotis.com/en/software/ ... abview.htm

:)
some information:

Robotis provides a detailed tutorial for interfacing their C DLL with LabVIEW. Their approach is also applicable to RoBoIO.DLL; when the official RoBoIO LabVIEW warper has not been released, if you need to use the new version of RoBoIO in LabVIEW, you may refer to Robotis approach:

http://support.robotis.com/en/software/ ... abview.htm

:)
roboard offline
Savvy Roboteer
Savvy Roboteer
Posts: 302
Joined: Fri Jul 03, 2009 4:44 am


4 postsPage 1 of 1
4 postsPage 1 of 1
cron